5
CONNECTING GAS SUPPLY TO BURNER ASSEMBLY
(If a Safety Pilot Kit is to be used, please refer to seperate instructions included with the kit.)
Natural Gas applications installedwithout a Safety Pilot Kit. LP/NG Safety Pilot Kit availableat yourlocal store.
A. Place burner pan assembly in the center of the fireplace.
B. Attach 3/8” Flare X 1/2” NPT gas valve (Part #13) to the 1/2 inch gas supply stub already in fireplace.
Be certain connections are tight and use pipe compound on all male NPT (pipe) threads to seal
joints.
C.
Attach 3/8” flared tubing (Part #15) to burner pan assembly.. Attach opposite end to gas supply line by
carefully bending the
flared tubing as needed to make the connection. Avoid kinking thetubing while
NOTE: Agood method of bending the tube is to fill it with sand, bending the tube as needed to make the
connection.This method will eliminate kinking in the line. Once the tube is in the desired configuration,
be sure to empty the tube completely of any sand before tube is connected to the gas supply line and
D.
Be certain all connections are tight. Only use pipe compound on all male NPT (pipe) threads.
Test all connections with a soapy water solution, and with the gas supply turned on. If bubbles appear
on any connection, tighten and re-test. Once it is determined there are no leaks whatsoever, turn off
gas supply and move to next assembly step.
GRANULE, EMBER AND GRATE PLACEMENT
A. Spread granules (Part # 16) over the installed burner pan. Granules
should be sloped to the same angle as the burner pan filling the entire
pan. (See Figure 7A.)
B. Spr
ead glowing embers (Part # 17) evenly over the top of the granules
covering the entire surface area, concentrating on the front and sides
of the burner pan for the most realistic burning effect.
C. Place log grate (Part # 7) over the burner pan aligning as shown.
(See Figure 7B.)
D.Attach back log Standoff(Part # 18) to the back part of the grate.
(See Figure 7B.)
NOTE: A hammer may be used to tap the back log stand-off in place.
It may be necessary to squeeze the back log stand-off with pliers afte
r
attaching to the grate.
(ManualValve / match lit only)
A. Open chimney
flue damper to the full open position.
B. Turn the gas control manual valve (Figure 9)clockwise to the full
OFF position.
C. W
ait five (5) minutes to clear out any gas. If you then smell gas, STOP!
Follow “A” in the safetyInformation above on this label. If you don't smell
gas, go to the next step.
D. Place a burning match on the surface of the burner embers (see figure 8)
Do not hold match in hand.Turn the manual gas valve counterclockwise
to the ON position.
.
Figure 7 ( A & B) Granule and
Grate Placement
Figure 8. Lighting the log set
bending. If tubing must be cut, use a tubing cutter. Flare the cut end of tube with a flaring tool.
burner assembl
y.
WARNING:For installation in a solid-fuel burning fireplace only. The
ust have a permanent vent opening toatmosphere
inches, or as determined from the
manufacturer's installation instructions.
fireplace chimney m
of not less than 49.2 square
TO TURN OFF GAS TO APPLIANCE
Turn the manual gas control valve (Figure 9) clockwise to the OFF position.
Figure 9. Manual gas valve
LIGHTING YOUR GAS LOG SET
(76 pagine)
(26 pagine)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale